消防泵9大常見問題與方法
來源：http://n3462.cn/ 日期：2023-04-11
現在這個社會消防泵的應用越來越廣泛,，被應用到很多消防行動和企業也被很多人所熟悉,，可是關于9大消防泵常見問題與方法大家可能還不是很了解，下面
川消廠家小編就和大家說一下,，讓您對它的了解更深,。
Now the application of fire pump in this society is more and more extensive, and it has been used in many fire actions and enterprises and is also familiar to many people. However, you may not know much about the common problems and solutions of the nine fire pump. Now let's talk about it in a small edition of Sichuan Fire Pump Factory to let you know more about it.
1,、葉輪或管線受堵
1. Impeller or pipeline blocked
措施：檢查有無障礙物。
Elimination measures: Check for obstacles.
2,、系統水頭太高
2. System head too high
措施：檢查系統的水頭(特別是磨擦損失),。
Elimination measures: Check the water head of the system (especially the friction loss).
3、無液體提供,，供給液體不足或壓力不足,，沒有注水或沒有適當排氣。
3. No liquid supply, insufficient liquid supply or pressure, no water injection or proper exhaust.
措施：檢查消防泵殼和入口管線是否全部注滿了液體,。
Elimination measures: check whether the fire pump shell and inlet pipeline are all filled with liquid.
4,、吸程太高
4. Suction head too high
措施：檢查現有的凈壓頭(入口管線太小或太長會造成很大的磨擦損失)。
Elimination measures: Check the existing net pressure head (if the inlet pipeline is too small or too long, it will cause significant friction loss).
5,、速度太低
5. Speed too low
措施：檢查電機的接線是否正確,，電壓是否正常或者透平的蒸汽壓力是否正常,。
Elimination measures: Check whether the wiring of the motor is correct, whether the voltage is normal, or whether the steam pressure of the turbine is normal.
6,、抽送熱的或揮發性液體時吸入水頭不足
6. Insufficient suction head when pumping hot or volatile liquids
措施：增大吸入水頭，向廠家咨詢,。
Elimination measures: Increase the suction head and consult the manufacturer.
7,、產生空氣或入口管線有泄漏
7. Air generation or leakage in the inlet pipeline
措施：檢查入口管線有無氣穴或空氣泄漏。
Elimination measures: Check the inlet pipeline for air pockets or air leaks.
8,、轉動方向不對
8. Wrong rotation direction
措施：檢查轉動方向,。
Elimination measure: Check the direction of rotation.
9、填料函中的填料或密封磨損,，使空氣漏入消防泵殼中,。
9. The packing or seal in the stuffing box is worn, making air leak into the fire pump shell.
措施：檢查填料或密封并按需要更換，檢查潤滑是否正常,。
Elimination measures: Check the packing or seal and replace it as needed, and check if the lubrication is normal.
經過小編的介紹相信您對我們公司
http://n3462.cn的消防泵更有了了解,，希望這次介紹會對您有幫助，以后小編會繼續補充關于消防泵的知識敬請期待吧,。
After the introduction of the editor, I believe you have a good understanding of our company http://n3462.cn I hope this presentation will be helpful to you. In the future, I will continue to supplement my knowledge about fire pump.
